Best Selling

Victron energy UTP Patch Lead 0.3m.

Victron energy UTP Patch Lead 1.8m.

Victron energy UTP Patch Lead 10m.

Victron energy UTP Patch Lead 20m.

Victron energy UTP Patch Lead 5m.

The BlueSolar PWM Light Charge Controller features a programable load output with lighting control mode and three stage battery charging.

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.

CE certified shore power cable with moulded 3 pin plug and connector. Features a power indication LED and protective cap on female connector for additional safety.

Victron Shore Power Cord, 32 Amp / 250Vac. 25 Metres.

Shunt 500A/50mV

A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.

Skylla-i (1+1): two isolated outputs to charge 2 battery banks. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery. Rugged - Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.

A powerful, waterproof and intelligent battery charger with a 7-stage adaptive charge algorithm, suitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm. The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air.

A powerful, waterproof and intelligent battery charger with a 7-stage adaptive charge algorithm, suitable for a wide range of battery types and chemistries featuring a dedicated Lithium-ion charge algorithm. The IP65 rating makes this charger especially suitable for marine, mobile, and industrial applications and it can withstand the rigors of an adverse environment: heat, humidity and salt air.

A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.  The right amount of charge for a lead-acid battery: variable absorption time BatterySafe mode: preventing damage due to excessive gassing Storage mode: less maintenance and aging when the battery is not in use Smaller and lighter compared to similar models NMEA2000 Canbus connection PowerControl: set a maximum shore power Remote Control Li-ion (LiFePo4) ready

One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ.

Features include: Temperature sensor, use as a power supply, forced cooling. Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally. The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Charge voltage 'absorption' / 'float': 28.5 V DC / 26.5 V DC. Charge current: 30 A. Charge characteristic: IUoUo (three step). Protection: output short circuit, battery reverse polarity detection, battery voltage too high, temperature too high. Operating temp. range -20 to 60°C (0 - 140°F). Humidity (non condensing) max 95%. Protection category IP 21.

Features include: Temperature sensor, use as a power supply, forced cooling. Input voltage / input voltage range: 230 V AC / 90 - 265 V AC. Frequency: 45-65 Hz / Power factor: 1. Charge voltage 'absorption' / 'float': 28.5 V DC / 26.5 V DC. Battery capacity: 250-500 Ah. Protection: IP21 / Output short circuit, battery reverse polarity detection, battery voltage too high, temperature too high. Charge current starter batt. / house batt.: 4 A / 50 A. Charge characteristic: IUoUo (three step). Remote alarm: Potential free contacts 60V / 1A (1x NO and 1x NC). Operating temp. range / Humidity (non condensing): -20 to 60°C / max 95%.

One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ.

One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. The input for the charger is 230V at 50/60HZ. Charge voltage can be measured directly on the battery terminals in order to compensate for voltage loss due to cable resistance. An external sensor allows measuring battery temperature and compensating charge voltage accordingly.

The Smart BMS CL 12/100 is a Battery Management system for Victron lithium-iron-phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator. The BMS CL 12/100 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources or DC loads in case of low battery voltage, high battery voltage or over temperature.

The SmartShunt is an all in one battery monitor, only without a display. A compatible smart phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on the phone (or tablet) and can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life.